Saver Safety Products

Honeywell low-profile Intelligent Photoelectric Sensor Flash Scan series detector sensitivity can be programmed in the control panel software. Sensitivity is continuously monitored and reported to the panel. Point ID capability allows each detector’s address to be set with rotary, decimal address switches, providing exact detector location for selective maintenance when chamber contamination reaches an unacceptable level.

• Stable communication technique with noise immunity
• Sleek, low-profile, stylish design
• Integral communications and built-in device-type identification
• Built-in tamper resistant feature
• Low standby current

t Saver Safety Products, we are committed to providing high-quality safety equipment designed to protect you and your team in any environment. Whether you're working in construction, manufacturing, healthcare, or any other industry, our innovative products are engineered to ensure the highest levels of protection, comfort, and durability.

• The Face Openeing should be fit and Flat
• The neck protector should not loose, but shouldBe fit and properly covering the shoulders too.
• The Hood should be double layered,Inset collar and face opening with elastic.

• The Hoods should have been tested as per EN13911:2004 in connection with EN 340:2003
• After 5 wash cycles.face opening is fit and flat fit.

• Outer Layer: Inherently Fire Retardant woven 360/410 GSM fabric.
• Inner Layer: Inherently Fire Retardant Non-woven fabric quilted to IFR woven fabric.
• Suit consists of Jacket Pant Hood with visor.

• Approved by UL Listed & FM ApprovedFINISH
• END CONNECTION: Flange X Flange
• NOMINAL SIZE 200, 150, 100 & 80 NB
• MAXIMUM SERVICE PRESSURE: 17.5 Bar (250 PSI)
• MOUNTING: Verticle
• FLANGE CONNECTION: ANSI B16.42
• TRIM: Galvanised fitting with Brass Valves
• FINISH: Red RAL 3001
• REFERENCE: NFPA 13 and NFPA 25

• Fireman Sabf Boots (safety toe cap + anti-perforation mid-sole)Excellent resistance to heat flow, heat contact, fire.
• Excellent resistance to chemicals : fuels, oils, weak and diluted acids, solvents.
• Excellent resistance to abrasion and cuts
• Used with chemical protective suits (satisfy permeation tests according to EN 943-2).

Single & Double Cabinet Hose Box Carbon Steel

Fire Cabinets are used to store the fire fighting equipment like Fire Hoses, Fire Extinguishers, Fire Hose Reels, Brachpipes etc. 

These cabinets provide best protection from the environmental damage to the fire equipment.

• Available Type: Abc, Co2, Foam Etc.
• Isi Marked & Irs Approved Fire Extenguishers
• Confirming To Is 14609,  Is 15683 & Is 7285 
• Controllable Discharge Mechanism, Pressure Gauge, Discharge Hose & Nozzle Epoxy
• Polyester Powder Coated As Per‘is 15683’isi Mark Fire Extinguishers Operating
• Temperature: - (-) 20ºc To (+) 55ºc Suitable For ‘a’ ‘b’ ‘c’ Class Of Fire
• Make- Safety First/safery Fire/shm

• A large switching capacity of 15 A with high repeat accuracy. 

• A wide range of variations in contact form for your selection: basic, split-contact, maintained-contact, and adjustable contact gap types. 

• A series of standard models for micro loads is available. 

• A series of molded terminal-type models incorporating safety terminal protective cover is available.

Detectors need removal and replacement for various reasons. The vast majority are fitted on bayonet mountings and the task can be done using specialist tools fitted to appropriate access poles. Using such specialist devices saves the time, cost, disruption and risk to safety that ladders, scaffolding or access gear represents.

Solo C3 – used in conjunction with Solo 330 / 332 dispensers - provides a safe way of achieving this with CO concentration levels high enough to activate an alarm, but low enough not to pose danger to user health.